Showing posts with label notebook. Show all posts
Showing posts with label notebook. Show all posts

Tuesday, January 13, 2009

Dell Latitude disassembly – LCD cover

I was asked by a friend to replace a lid cover to his Dell Latitude D600 notebook. In my previous post I I covered removing the keyboard and hinge cover. This was the first step in removing the lid cover. His was a bit scratched and the hinges were in poor shape just barely hanging on. Also the locking latch was not lined up correctly so it wasn’t staying shut. The tools you’ll need are the same as before. A small Phillips and flathead screwdriver are essential.

IMG_3524

Here we have the left hand hinge which looks in pretty sorry state. It was very loose and there was space between the hinge in the case. This wasn’t going to last much longer.

IMG_3526

Here’s our Dell with the keyboard and hinge cover removed.

 

IMG_3527

First thing I did was disconnect the LCD display connector from the board.

IMG_3528

It has a small ground strap and a wire connected to the LCD.

IMG_3529

First I unscrewed the ground strap and then disconnected it. It has small handle to aid in pull.

IMG_3531

Now I move on to the hinges. The left hand side has two screws and the other has one.

IMG_3532

After the screws are removed it should lift right out of place.

IMG_3544

Now I’m removing the frame around LCD display. In this case I’m just replacing the lid cover. This would a good reference if your replacing the actual LCD screen too. There are 4 screws along the top edge and 2 in the bottom corner.

IMG_3547

 

After the screws are removed you can then begin gently prying the lid cover apart. I used a small flathead screwdriver. B gently when using this as you could damage the the plastic casing. They do make plastic tools to do this which I do have on order.

IMG_3548

I now have the frame off.

IMG_3550

Remove the screws holding the LCD display in place.

IMG_3555

Lift and remove display. It’s that simple. To assemble just go in reverse order. Here I’m replacing the lid so I just lifted it out the old one and into the new one. I reassembled it. It was easier than I thought it would be. This took me about 30 minute or so. After I put it together and rebooted. It worked great. Thanks for coming by

Parts: Parts-People.com

Source: Dell Latitude D600 Service manual

Saturday, January 10, 2009

Dell Latitude gets a boost

IMG_3507 A friend of mine asked me to upgrade his memory in his laptop. The patient is a Dell Latitude D600. It had been running with 512mb of RAM with Windows XP Professional. He decided it was time for a boost. I thought I’d show here just how easy it is to upgrade your memory in your laptop.

First step was purchasing the RAM. A common question for computer is what kind of RAM (or memory) do I get. With all the different types of RAM out there and not to mention the technical jargon it can be confusing. I don’t even understand many of them either. My favorite place to purchase RAM is Crucial.com. If you you go to there website they have a memory configurator which helps you out. They have a manual method which you look up your make, model of your machine. They also can scan your computer which takes any guess work out of the equation.

The parts and tools needed:

  • RAM – Crucial Part # CT12864x335, 1GB 200-PIN SODIMM 128MX64 DDR PC2700
  • Small Phillips head screwdriver IMG_3501

Obviously you need the Dell Latitude D600 too. The first thing you’ll have to do is locate where the memory goes. Well you flip over the Dell and it’s located in one of the secret compartments. Dell was nice enough to mark the door with a “M” just to side of it. It’s the 2” x 3” door just off center. It’s just located beneath the COA sticker in the picture . Located on the bottom is a small screw. Now is when you’ll get to use your Phillips screwdriver.


IMG_3503

IMG_3504 Once you open the door you’ll see your two banks of memory cards. Gently pull the two tabs alongside the memory bank.

IMG_3505

Lift up and pull it out.

IMG_3506

Insert your new new memory chip. Don’t worry they are notched so it only goes back in one way. Reassemble in reverse order. After all is put back together I rebooted the computer to make sure everything went well. It now has a healthy 1.25 Gb’s of RAM. This only took about 15 minutes to do. Next up will be removing the keyboard so stay tuned. Thanks for coming by!

Sources: